C500 SIDESTREAM ETCO2 MODULE SPECIFICATIONS

Transducer Type

Mainstream CO2 sensor

Principle of Operation

Non-dispersive infrared (NDIR) single beam optics,

dual wavelength, no moving parts

Initialization Time

Capnogram displayed in less than 3 seconds, at an ambient temperature of 25∩, full specifications within 30 seconds

CO2 Measurement Range

0 to 150 mmHg, 0 to 19.7%, 0 to 20 kPa

CO2 Calculation Method

BTPS (Body Temperature Pressure Saturated)

CO2 Rise Time (10 - 90% of step change of final CO2 value)

Less than 8 ms - Adult reusable or single patient use

Less than 8 ms - Infant reusable or single patient use

CO2 Resolution

0.01 mmHg 0 to 69 mmHg, 0.02 mmHg 70 to 150 mmHg

CO2 Accuracy *

0 - 40 mmHg 【2 mmHg 41 - 70 mmHg 【5% of reading 71 - 100 mmHg 【8% of reading 101 - 150 mmHg 【10% of reading * NOTE: Temperature at 35 ∩.

CO2 Stability

Short Term Drift: Drift over four hours shall not exceed

2 mmHg maximum.

Long Term Drift: Accuracy specification will be maintained

over a 120 hour period.

CO2 Noise

RMS noise of the sensor shall be less than or equal to 0.25 mmHg

at 7.5% CO2

Sampling Rate

100 Hz

Respiration Rate Range

2 to 150 breaths per minute (BPM)

Respiration Rate Accuracy

【1 breath

Calibration

No routine user calibration required. An airway adapter zero is required

when insert an airway adapter.

Safety lock-outs:

≤System does not allow adapter zero for 20 seconds after

the last breath is detected.

≤System does not allow adapter zero if temperature

is not stable.

≤System does not allow adapter zero if there is CO2 gas

in the airway adapter.

ETCO2 Calculation

Method: Peak of the expired CO2 waveform

Selections: 1 breath, 10 second, 20 second

Note: the minimum reported differential value between

the baseline and the CO2 value shall be 5 mmHg.

Inspired CO2Measurement

Range: 3 to 50 mmHg

Method: Lowest reading of the CO2 waveform in the previous 20 seconds

Compensations (Host Controlled)

Compensations for: Expired O2 , balance gas (N2 , N2 O, He) and anesthetic

agents Uses gas compensation information and barometric pressure to correct

the raw carbon dioxide value

O2 Compensation

Range: 0 to 100%

Resolution: 1%

Default: 16%

N2O Compensation

Range: 0 (off) or 1 (on)

Default: Off

Note: If ON, the balance of the mixture is O2

He Compensation

Range: 0 (off) or 1 (on)

Default: Off

Note: If ON, the balance of the mixture is O2

Total Pressure

Range: 400-850 mmHg.

Total pressure = Barometric plus Airway pressure.

Barometric pressure provided by host.

Recomended accuracy of pressure transducer: 【1% FS

Airway Adapter Type

Pediatric/Adult Reusable Airway Adapter,

Infant/Pediatric Reusable Airway Adapter

Input Voltage

5.00 Volts (【 5%)

Power Consumption

900mW (typical)

Warm-up Time

3 seconds

Interface

Highly configurable serial digital interface(TTL/RS232),

CO2 waveform data, Breath Detect Algorithm data

Temperature and Humidity

Operating: 0 to 50ìC, 10 to 90% RH, non-condensing

Storage: -40 to 70ìC, <90% RH, non-condensing

Dimensions

50mm*22mm*36mm

Weight

< 95 grams

Interconnection

Standard Lemo Redel 8-pin plastic Material PSU Pin out:1 VA 5.0V;

2 Shield Shield;3 DGND Digital return;4 VA 5.0V;

5 TxD Serial data from the Module;6 RxD Serial data from Host;

7 AGND Analog return;8 NC

● Response is faster and there is less chance of erroneous, artifact data.

● There are no pumping or pneumatic components to replace thus maintenance requirements and

overall cost-of -ownership are minimized.

● Better policy of after service. Manufacturer promises that the module can be replaced by a new one

if it is not damaged by man-made in one year.

● Long-lasting life for the infrared light receiver.